Don't like ads? PRO users don't see any ads ;-)
Public Pastes
Guest

KillaB

By: a guest on Aug 30th, 2010  |  syntax: None  |  size: 11.08 KB  |  hits: 101  |  expires: Never
download  |  raw  |  embed  |  report abuse  |  print
Text below is selected. Please press Ctrl+C to copy to your clipboard. (⌘+C on Mac)
  1. ADAM2 Revision 0.18.01
  2.  
  3. (C) Copyright 1996-2003 Texas Instruments Inc. All Rights Reserved.
  4.  
  5. (C) Copyright 2003 Telogy Networks, Inc.
  6.  
  7. Usage: setmfreq [-d] [-s sys_freq, in MHz] [cpu_freq, in MHz]
  8.  
  9. Memory optimization Complete!
  10.  
  11.  
  12.  
  13. DGB34 >
  14.  
  15. Press any key to abort OS load, or wait 3 seconds for OS to boot...
  16.  
  17. checksum error
  18.  
  19.  
  20.  
  21. Linux version 2.6.32.16 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Wed Aug 25 16:12:51 PDT 2010
  22.  
  23. bootconsole [early0] enabled
  24.  
  25. CPU revision is: 00018448 (MIPS 4KEc)
  26.  
  27. TI AR7 (TNETD7300), ID: 0x0005, Revision: 0x02
  28.  
  29. Determined physical RAM map:
  30.  
  31.  memory: 01000000 @ 14000000 (usable)
  32.  
  33. Initrd not found or empty - disabling initrd
  34.  
  35. Zone PFN ranges:
  36.  
  37.   Normal   0x00014000 -> 0x00015000
  38.  
  39. Movable zone start PFN for each node
  40.  
  41. early_node_map[1] active PFN ranges
  42.  
  43.     0: 0x00014000 -> 0x00015000
  44.  
  45. Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
  46.  
  47. Kernel command line: rootfstype=squashfs,jffs2 console=ttyS0,115200n8
  48.  
  49. PID hash table entries: 64 (order: -4, 256 bytes)
  50.  
  51. Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
  52.  
  53. Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
  54.  
  55. Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
  56.  
  57. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
  58.  
  59. Memory: 12352k/16384k available (2251k kernel code, 4032k reserved, 356k data, 136k init, 0k highmem)
  60.  
  61. Hierarchical RCU implementation.
  62.  
  63. NR_IRQS:256
  64.  
  65. Calibrating delay loop... 149.50 BogoMIPS (lpj=747520)
  66.  
  67. Mount-cache hash table entries: 512
  68.  
  69. NET: Registered protocol family 16
  70.  
  71. bio: create slab <bio-0> at 0
  72.  
  73. Switching to clocksource MIPS
  74.  
  75. NET: Registered protocol family 2
  76.  
  77. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  78.  
  79. TCP established hash table entries: 512 (order: 0, 4096 bytes)
  80.  
  81. TCP bind hash table entries: 512 (order: -1, 2048 bytes)
  82.  
  83. TCP: Hash tables configured (established 512 bind 512)
  84.  
  85. TCP reno registered
  86.  
  87. NET: Registered protocol family 1
  88.  
  89. squashfs: version 4.0 (2009/01/31) Phillip Lougher
  90.  
  91. Registering mini_fo version $Id$
  92.  
  93. JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
  94.  
  95. msgmni has been set to 24
  96.  
  97. io scheduler noop registered
  98.  
  99. io scheduler deadline registered (default)
  100.  
  101. Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
  102.  
  103. serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a 16550A
  104.  
  105. console [ttyS0] enabled, bootconsole disabled
  106.  
  107. console [ttyS0] enabled, bootconsole disabled
  108.  
  109. serial8250: ttyS1 at MMIO 0x8610f00 (irq = 16) is a 16550A
  110.  
  111. physmap platform flash device: 00800000 at 10000000
  112.  
  113. physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
  114.  
  115.  CFI mfr 0x000000c2
  116.  
  117.  CFI id  0x000022a8
  118.  
  119.  Amd/Fujitsu Extended Query Table at 0x0040
  120.  
  121.   Amd/Fujitsu Extended Query version 1.1.
  122.  
  123. number of CFI chips: 1
  124.  
  125. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
  126.  
  127. cmdlinepart partition parsing not available
  128.  
  129. RedBoot partition parsing not available
  130.  
  131. 4 ar7part partitions found on MTD device physmap-flash.0
  132.  
  133. Creating 4 MTD partitions on "physmap-flash.0":
  134.  
  135. 0x000000000000-0x000000010000 : "loader"
  136.  
  137. 0x0000003f0000-0x000000400000 : "config"
  138.  
  139. 0x000000020000-0x0000003f0000 : "linux"
  140.  
  141. 0x000000100000-0x0000003f0000 : "rootfs"
  142.  
  143. mtd: partition "rootfs" set to be root filesystem
  144.  
  145. mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000
  146.  
  147. 0x0000002b0000-0x0000003f0000 : "rootfs_data"
  148.  
  149. Fixed MDIO Bus: probed
  150.  
  151. cpmac-mii: probed
  152.  
  153. cpmac: device eth0 (regs: 08612800, irq: 41, phy: 1:10, mac: 00:0f:b5:b3:00:00)
  154.  
  155. cpmac: device eth1 (regs: 08610000, irq: 27, phy: 1:1f, mac: 00:0f:b5:b3:00:00)
  156.  
  157. Registered led device: ppp
  158.  
  159. Registered led device: status
  160.  
  161. Registered led device: adsl
  162.  
  163. Registered led device: wifi
  164.  
  165. Registered led device: power
  166.  
  167. vlynq0: regs 0x08611800, irq 29, mem 0x04000000
  168.  
  169. Found a VLYNQ device: 00000009
  170.  
  171. vlynq1: regs 0x08611c00, irq 33, mem 0x0c000000
  172.  
  173. TCP westwood registered
  174.  
  175. NET: Registered protocol family 17
  176.  
  177. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  178.  
  179. All bugs added by David S. Miller <davem@redhat.com>
  180.  
  181. VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
  182.  
  183. Freeing unused kernel memory: 136k freed
  184.  
  185. Please be patient, while OpenWrt loads ...
  186.  
  187. - preinit -
  188.  
  189. Press the [f] key and hit [enter] to enter failsafe mode
  190.  
  191. - regular preinit -
  192.  
  193. switching to jffs2
  194.  
  195. mini_fo: using base directory: /
  196.  
  197. mini_fo: using storage directory: /overlay
  198.  
  199. - init -
  200.  
  201.  
  202.  
  203. Please press Enter to activate this console. device eth0 entered promiscuous mode
  204.  
  205. br-lan: port 1(eth0) entering forwarding state
  206.  
  207. br-lan: port 1(eth0) entering disabled state
  208.  
  209. device eth1 entered promiscuous mode
  210.  
  211. br-lan: port 2(eth1) entering forwarding state
  212.  
  213. br-lan: port 2(eth1) entering disabled state
  214.  
  215. NET: Registered protocol family 8
  216.  
  217. NET: Registered protocol family 20
  218.  
  219. PPP generic driver version 2.4.2
  220.  
  221. ip_tables: (C) 2000-2006 Netfilter Core Team
  222.  
  223. NET: Registered protocol family 24
  224.  
  225. nf_conntrack version 0.5.0 (195 buckets, 780 max)
  226.  
  227. CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  228.  
  229. nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  230.  
  231. sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  232.  
  233. acx: this driver is still EXPERIMENTAL
  234.  
  235. acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
  236.  
  237. acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
  238.  
  239. acx: running on a little-endian CPU
  240.  
  241. acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
  242.  
  243. Driver found for VLYNQ device: 00000009
  244.  
  245. acx: found TI TNETW1130-based wireless network card at <NULL>, irq:80, phymem:0x4000000, mem:0xa4000000
  246.  
  247. initial debug setting is 0x000A
  248.  
  249. using IRQ 80
  250.  
  251. acx: need to load firmware for acx111 chipset with radio ID 16, please provide via firmware hotplug:
  252.  
  253. acx: either one file only (<c>ombined firmware image file, radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific extension file)
  254.  
  255. requesting firmware image 'tiacx111c16'
  256.  
  257. acx_vlynq vlynq0: firmware: requesting tiacx111c16
  258.  
  259. acx_write_fw (main/combined): 0
  260.  
  261. acx_validate_fw (main/combined): 0
  262.  
  263. initializing max packet templates
  264.  
  265. dump queue head (from card):
  266.  
  267. len: 24
  268.  
  269. tx_memory_block_address: 19E40
  270.  
  271. rx_memory_block_address: 15240
  272.  
  273. tx1_queue address: 14774
  274.  
  275. rx1_queue address: 14434
  276.  
  277. NVS_vendor_offs:01CD probe_delay:200 eof_memory:1114112
  278.  
  279. CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
  280.  
  281. AntennaID:00 Len:02 Data:01 02
  282.  
  283. PowerLevelID:01 Len:02 Data:001E 000A
  284.  
  285. DataRatesID:02 Len:05 Data:02 04 11 22 44
  286.  
  287. DomainID:03 Len:06 Data:10 20 30 31 32 40
  288.  
  289. ProductID:04 Len:09 Data:TI ACX100
  290.  
  291. ManufacturerID:05 Len:07 Data:TI Test
  292.  
  293. get_mask 0x00004182, set_mask 0x00000000
  294.  
  295. don't know how to get sensitivity for radio type 0x16
  296.  
  297. got sensitivity value 0
  298.  
  299. got antenna value 0x4A
  300.  
  301. got regulatory domain 0x10
  302.  
  303. get_mask 0x00000000, set_mask 0x00000000 - after update
  304.  
  305. new ratevector: 82 84 0B 0C 12 16 18 24 2C 30 48 60 6C
  306.  
  307. setting RXconfig to 2010:0FDD
  308.  
  309. acx: === chipset TNETW1130, radio type 0x16 (Radia), form factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 2.3.1.31' ===
  310.  
  311. creating /proc entry driver/acx_wlan%d
  312.  
  313. creating /proc entry driver/acx_wlan%d_diag
  314.  
  315. creating /proc entry driver/acx_wlan%d_eeprom
  316.  
  317. creating /proc entry driver/acx_wlan%d_phy
  318.  
  319. acx v0.3.37: net device wlan%d, driver compiled against wireless extensions 22 and Linux 2.6.32.16
  320.  
  321. using IRQ 80
  322.  
  323. registered device TI Avalanche SAR
  324.  
  325. Sangam detected
  326.  
  327. requesting firmware image "ar0700xx.bin"
  328.  
  329.  avsar: firmware: requesting ar0700xx.bin
  330.  
  331. tn7dsl_set_modulation : Setting mode to 0x10
  332.  
  333. Creating new root folder avalanche in the proc for the driver stats
  334.  
  335. Texas Instruments ATM driver: version:[7.03.01.00]
  336.  
  337.  
  338.  
  339.  
  340.  
  341.  
  342.  
  343. BusyBox v1.15.3 (2010-07-10 11:38:40 PDT) built-in shell (ash)
  344.  
  345. Enter 'help' for a list of built-in commands.
  346.  
  347.  
  348.  
  349.   _______                     ________        __
  350.  
  351.  |       |.-----.-----.-----.|  |  |  |.----.|  |_
  352.  
  353.  |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
  354.  
  355.  |_______||   __|_____|__|__||________||__|  |____|
  356.  
  357.           |__| W I R E L E S S   F R E E D O M
  358.  
  359.  Backfire (10.03.1-rc3, r22796) --------------------
  360.  
  361.   * 1/3 shot Kahlua    In a shot glass, layer Kahlua
  362.  
  363.   * 1/3 shot Bailey's  on the bottom, then Bailey's,
  364.  
  365.   * 1/3 shot Vodka     then Vodka.
  366.  
  367.  ---------------------------------------------------
  368.  
  369. root@OpenWrt:/# ifconfig
  370.  
  371. br-lan    Link encap:Ethernet  HWaddr 00:0F:B5:B3:00:00  
  372.  
  373.           inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
  374.  
  375.           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
  376.  
  377.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  378.  
  379.           TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
  380.  
  381.           collisions:0 txqueuelen:0
  382.  
  383.           RX bytes:0 (0.0 B)  TX bytes:402 (402.0 B)
  384.  
  385.  
  386.  
  387. eth0      Link encap:Ethernet  HWaddr 00:0F:B5:B3:00:00  
  388.  
  389.           UP BROADCAST MULTICAST  MTU:1500  Metric:1
  390.  
  391.           RX packets:102 errors:0 dropped:0 overruns:0 frame:0
  392.  
  393.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  394.  
  395.           collisions:0 txqueuelen:1000
  396.  
  397.           RX bytes:12943 (12.6 KiB)  TX bytes:0 (0.0 B)
  398.  
  399.           Interrupt:41
  400.  
  401.  
  402.  
  403. eth1      Link encap:Ethernet  HWaddr 00:0F:B5:B3:00:00  
  404.  
  405.           UP BROADCAST MULTICAST  MTU:1500  Metric:1
  406.  
  407.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  408.  
  409.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  410.  
  411.           collisions:0 txqueuelen:1000
  412.  
  413.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  414.  
  415.           Interrupt:27
  416.  
  417.  
  418.  
  419. lo        Link encap:Local Loopback  
  420.  
  421.           inet addr:127.0.0.1  Mask:255.0.0.0
  422.  
  423.           UP LOOPBACK RUNNING  MTU:16436  Metric:1
  424.  
  425.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
  426.  
  427.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
  428.  
  429.           collisions:0 txqueuelen:0
  430.  
  431.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
  432.  
  433.  
  434.  
  435. root@OpenWrt:/# cat /etc/config/network
  436.  
  437. # Copyright (C) 2006 OpenWrt.org
  438.  
  439.  
  440.  
  441. config interface loopback
  442.  
  443.         option ifname   lo
  444.  
  445.         option proto    static
  446.  
  447.         option ipaddr   127.0.0.1
  448.  
  449.         option netmask  255.0.0.0
  450.  
  451.  
  452.  
  453. config interface lan
  454.  
  455.         option type     bridge
  456.  
  457.         option ifname   "eth0 eth1"
  458.  
  459.         option proto    static
  460.  
  461.         option ipaddr   192.168.1.1
  462.  
  463.         option netmask  255.255.255.0
  464.  
  465.         option nat      1
  466.  
  467.  
  468.  
  469. ## Example for ATM bridging.
  470.  
  471. ## Useful for PPPoE or IP over ATM. Will create 'nas${unit}'
  472.  
  473. #
  474.  
  475. # config atm-bridge
  476.  
  477. #       option unit     0
  478.  
  479. #       option encaps   llc
  480.  
  481. #       option vpi      8
  482.  
  483. #       option vci      35
  484.  
  485. #       option payload  bridged # some ISPs need this set to 'routed'
  486.  
  487.  
  488.  
  489.  
  490.  
  491. # config interface wan
  492.  
  493. ##      PPPoE:
  494.  
  495. #       option ifname   nas0
  496.  
  497. #       option proto    pppoe
  498.  
  499.  
  500.  
  501. ##      PPPoA:
  502.  
  503. #       option ifname   atm0
  504.  
  505. #       option proto    pppoa
  506.  
  507. #       option encaps   llc
  508.  
  509. #       option vpi      8
  510.  
  511. #       option vci      35
  512.  
  513.  
  514.  
  515. ##      Both:
  516.  
  517. #       option username "my_username"
  518.  
  519. #       option password "my_password"
  520.  
  521. root@OpenWrt:/#
create a new version of this paste RAW Paste Data