2016-06-26 17:09:06  ★ Matt Hammond nods slightly as he takes the brakes, looking at the box silently for a brief while.
2016-06-26 17:09:48  ★ Matt Hammond tears the box open and peeps inside it, prior to nod in a somewhat slow pace.
2016-06-26 17:10:34  ★ Matt Hammond exhales deeply as he sits down next to the frontal left wheel.
2016-06-26 17:11:05  ★ Matt Hammond grasps on the toolbox as he slides it next to him.
2016-06-26 17:11:22  ★ Loud clasping would be produced from the box as it'd be slided through the rough surface.      ((Matt Hammond))
2016-06-26 17:12:31  ★ Matt Hammond opens the big toolbox and grasps on a car jack, prior to slide it next to the wheel he's -
2016-06-26 17:12:37  ★ - going to work on.      ((Matt Hammond))
2016-06-26 17:13:16  ★ Matt Hammond fits the metal lever in place as he starts pulling it down and up fastly.
2016-06-26 17:13:43  ★ Matt would come to a stop when the frontal left wheel would be barely lifted off the floor.      ((Matt Hammond))
2016-06-26 17:14:15   [English] Matt Hammond says: Okay.
2016-06-26 17:15:31  ★ Matt Hammond digs inside the tool box and gets a lug wrench.
2016-06-26 17:15:56  ★ Matt Hammond position the lug wrench on the upper nut, the first of the 6, and starts spinning it -
2016-06-26 17:16:20  ★ - fastly and repeatly, until it'd be loosen enough to continue taking it out by manually by-      ((Matt Hammond))
2016-06-26 17:16:22  ★ - hand.      ((Matt Hammond))
2016-06-26 17:16:34  ★ Matt would continue to take the rest of the nuts the same way.      ((Matt Hammond))
2016-06-26 17:18:24  ★ Matt Hammond places each of his hands on the sides of the wheel, and holds it tightly, prior to -
2016-06-26 17:18:32  ★ - slide it backwards.      ((Matt Hammond))
2016-06-26 17:18:59  ★ The wheel would slide off the truck.      ((Matt Hammond))
2016-06-26 17:19:25  ★ Matt Hammond turns his torso leftwards, laying the wheel down next to him.
2016-06-26 17:19:37   [English] Matt Hammond says: Okay.
2016-06-26 17:20:48  ★ Matt Hammond focuses on the caliper and carefully looks for the pins that'd be holding the caliper in -
2016-06-26 17:20:50  ★ - place.      ((Matt Hammond))
2016-06-26 17:22:07  ★ After a brief moment, Matt would find the pins.      ((Matt Hammond))
2016-06-26 17:22:41  ★ Matt Hammond gets ahold of a wrench from inside the toolbox, and looks towards the caliper once again.
2016-06-26 17:23:22  ★ Matt Hammond uses the wrench to take both nuts out of the pins.
2016-06-26 17:24:06  ★ Matt Hammond carefully slides both of them out, and lays them next to the wheel.
2016-06-26 17:24:55  ★ Matt Hammond  lays his right hand on the bottom end of the caliper, and pivots it upwards.
2016-06-26 17:25:43  ★ Matt Hammond gets ahold of the closest brake pad, and slides it out of its place, prior to do the same -
2016-06-26 17:25:54  ★ - with the other one on the other side.      ((Matt Hammond))
2016-06-26 17:26:27  ★ Matt Hammond  carelessly tosses them away, and digs his hand inside the box to get a pair of the -
2016-06-26 17:26:34  ★ - brand new ceramic brake pads.      ((Matt Hammond))
2016-06-26 17:27:54  ★ Matt Hammond reaches inside the box to get one of the small packets of grease.
2016-06-26 17:28:32  ★ Matt Hammond tears it open, and applies some of this gray-ish grease on the new calipers' -
2016-06-26 17:28:38  ★ - retaining clips.      ((Matt Hammond))
2016-06-26 17:29:10  ★ Matt Hammond slides the brand new brakes in place the same way he took the other ones.
2016-06-26 17:32:22  ★ Matt Hammond coughs slightly as he guides his right hand towards the toolbox, reaching for a c-clamp -
2016-06-26 17:32:31  ★ - from inside it.      ((Matt Hammond))
2016-06-26 17:33:56  ★ Matt Hammond applies the c-clamp on the caliper in order to fully retract the pistons on the -
2016-06-26 17:34:11  ★ - caliper.      ((Matt Hammond))
2016-06-26 17:36:24  ★ Matt Hammond lays his thumb on the caliper, and slides it downwards and back to their original position,-
2016-06-26 17:36:24  ★ - apparently with little effort.      ((Matt Hammond))
2016-06-26 17:37:39  ★ reinstalls the slider bolts and wheel back on the vehicle by repeating the process he -      ((Matt Hammond))
2016-06-26 17:37:56  ★ - did with them invertidly.      ((Matt Hammond))
2016-06-26 17:39:01  ★ Matt Hammond finally repeats the process of changing the brake pads on the resting wheels.
2016-06-26 17:39:36  ★ Matt Hammond  hops inside the truck and slides the key in a 60º degree angle, turning the ignition on.
2016-06-26 17:40:04  ★ Matt Hammond presses on the brakes repeatly at least 30 times.