Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Starting program at 0x80010000
- [ 0.000000] Linux version 3.3.7 (chisco@chisco-aluminio) (gcc version 4.6.3 20120201 (prerelease) (Li2
- [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
- [ 0.000000] CPU frequency is 320 MHz
- [ 0.000000] 32MB of RAM installed
- [ 0.000000] registering 32 GPIOs
- [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
- [ 0.000000] board_bcm963xx: Boot address 0xb8000000
- [ 0.000000] board_bcm963xx: CFE version: unknown
- [ 0.000000] bootconsole [early0] enabled
- [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
- [ 0.000000] board_bcm963xx: board name: 963281T_TEF
- [ 0.000000] Determined physical RAM map:
- [ 0.000000] memory: 02000000 @ 00000000 (usable)
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Zone PFN ranges:
- [ 0.000000] Normal 0x00000000 -> 0x00002000
- [ 0.000000] Movable zone start PFN for each node
- [ 0.000000] Early memory PFN ranges
- [ 0.000000] 0: 0x00000000 -> 0x00002000
- [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
- [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
- [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0
- [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
- [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
- [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
- [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
- [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
- [ 0.000000] Memory: 29416k/32768k available (2219k kernel code, 3352k reserved, 396k data, 196k init,)
- [ 0.000000] NR_IRQS:128
- [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
- [ 0.036000] pid_max: default: 32768 minimum: 301
- [ 0.040000] Mount-cache hash table entries: 512
- [ 0.048000] NET: Registered protocol family 16
- [ 0.276000] registering PCI controller with io_map_base unset
- [ 0.284000] bio: create slab <bio-0> at 0
- [ 0.288000] PCI host bridge to bus 0000:00
- [ 0.292000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
- [ 0.296000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
- [ 0.300000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
- [ 0.304000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
- [ 0.308000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
- [ 0.312000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
- [ 0.316000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
- [ 0.320000] Switching to clocksource MIPS
- [ 0.328000] NET: Registered protocol family 2
- [ 0.332000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.340000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
- [ 0.348000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
- [ 0.356000] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.360000] TCP reno registered
- [ 0.364000] UDP hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.372000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
- [ 0.380000] NET: Registered protocol family 1
- [ 0.384000] audit: initializing netlink socket (disabled)
- [ 0.392000] type=2000 audit(0.392:1): initialized
- [ 0.396000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.404000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat,.
- [ 0.412000] msgmni has been set to 57
- [ 0.416000] io scheduler noop registered
- [ 0.420000] io scheduler deadline registered (default)
- �[ 0.436000] console [ttyS0] enabled, bootconsole disabled= 36) is a bcm63xx_uart
- [ 0.436000] console [ttyS0] enabled, bootconsole disabled
- [ 0.456000] m25p80 spi0.0: found mx25l12805d, expected m25p80
- [ 0.464000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
- [ 0.468000] bcm63xxpart: CFE boot tag found with version 6 and board type 963281T_TEF
- [ 0.476000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
- [ 0.484000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00
- [ 0.488000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000
- [ 0.496000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
- [ 0.504000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
- [ 0.512000] bcm63xxpart: Spare partition is offset 2c0004 and length d2fffc
- [ 0.520000] 5 bcm63xxpart partitions found on MTD device spi0.0
- [ 0.524000] Creating 5 MTD partitions on "spi0.0":
- [ 0.528000] 0x000000000000-0x000000010000 : "CFE"
- [ 0.536000] 0x000000010100-0x000000100000 : "kernel"
- [ 0.544000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller thy
- [ 0.560000] 0x000000100000-0x000000ff0000 : "rootfs"
- [ 0.568000] mtd: partition "rootfs" set to be root filesystem
- [ 0.572000] mtd: partition "rootfs_data" created automatically, ofs=2C0000, len=D30000
- [ 0.580000] 0x0000002c0000-0x000000ff0000 : "rootfs_data"
- [ 0.588000] 0x000000ff0000-0x000001000000 : "nvram"
- [ 0.596000] 0x000000010000-0x000000ff0000 : "linux"
- [ 0.640000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
- [ 0.652000] TCP westwood registered
- [ 0.656000] NET: Registered protocol family 17
- [ 0.660000] 8021q: 802.1Q VLAN Support v1.8
- [ 0.676000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
- [ 0.684000] Freeing unused kernel memory: 196k freed
- awk: /proc/cpuinfo: No such file or directory
- [ 3.256000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
- [ 3.416000] roboswitch: Probing device eth0:
- [ 3.420000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external
- [ 3.428000] No Robo switch in managed mode found, phy_id = 0xffffffff
- [ 3.436000] roboswitch: Probing device eth1: No such device
- [ 3.440000] roboswitch: Probing device eth2: No such device
- [ 3.444000] roboswitch: Probing device eth3: No such device
- - preinit -
- Press the [f] key and hit [enter] to enter failsafe mode
- - regular preinit -
- [ 9.452000] JFFS2 notice: (318) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of .
- switching to jffs2
- - init -
- Please press Enter to activate this console. [ 11.072000] Compat-wireless backport release: compat-wir7
- [ 11.080000] Backport based on wireless-testing.git master-2012-05-29
- [ 11.088000] compat.git: wireless-testing.git
- [ 11.148000] cfg80211: Calling CRDA to update world regulatory domain
- [ 11.152000] cfg80211: World regulatory domain updated:
- [ 11.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
- [ 11.168000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 11.176000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 11.184000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
- [ 11.192000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 11.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
- [ 11.668000] SCSI subsystem initialized
- [ 11.712000] There is already a switch registered on the device 'eth0'
- [ 11.720000] roboswitch: Probing device eth1: No such device
- [ 11.728000] roboswitch: Probing device eth2: No such device
- [ 11.732000] roboswitch: Probing device eth3: No such device
- [ 12.036000] usbcore: registered new interface driver usbfs
- [ 12.044000] usbcore: registered new interface driver hub
- [ 12.052000] usbcore: registered new device driver usb
- [ 12.748000] Broadcom 43xx driver loaded [ Features: PNL ]
- [ 12.776000] Button Hotplug driver version 0.4.1
- [ 13.576000] PPP generic driver version 2.4.2
- [ 14.588000] ip_tables: (C) 2000-2006 Netfilter Core Team
- [ 14.872000] NET: Registered protocol family 24
- [ 15.096000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 15.136000] nf_conntrack version 0.5.0 (462 buckets, 1848 max)
- [ 15.832000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 16.044000] usbcore: registered new interface driver snd-usb-audio
- [ 16.164000] Initializing USB Mass Storage driver...
- [ 16.172000] usbcore: registered new interface driver usb-storage
- [ 16.176000] USB Mass Storage support registered.
- [ 20.444000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
- [ 20.464000] device eth0 entered promiscuous mode
- [ 20.472000] br-lan: port 1(eth0) entered forwarding state
- [ 20.476000] br-lan: port 1(eth0) entered forwarding state
- [ 22.480000] br-lan: port 1(eth0) entered forwarding state
- BusyBox v1.19.4 (2012-06-01 22:00:12 WEST) built-in shell (ash)
- Enter 'help' for a list of built-in commands.
- _______ ________ __
- | |.-----.-----.-----.| | | |.----.| |_
- | - || _ | -__| || | | || _|| _|
- |_______|| __|_____|__|__||________||__| |____|
- |__| W I R E L E S S F R E E D O M
- -----------------------------------------------------
- ATTITUDE ADJUSTMENT (Bleeding Edge, r32035)
- -----------------------------------------------------
- * 1/4 oz Vodka Pour all ingredients into mixing
- * 1/4 oz Gin tin with ice, strain into glass.
- * 1/4 oz Amaretto
- * 1/4 oz Triple sec
- * 1/4 oz Peach schnapps
- * 1/4 oz Sour mix
- * 1 splash Cranberry juice
- -----------------------------------------------------
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement