Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- Please put your device to Force USB Recovery Mode, when your are ready, ter key
- To place system in Force USB Recovery Mode:
- 1. Power down the device. If connected, remove the AC adapter from the dhe device MUST be powered OFF, not in a suspend or sleep state.
- 2. Connect the Micro-B plug on the USB cable to the Recovery (USB Micro-on the device and the other end to an available USB port on the host PC.
- 3. Connect the power adapter to the device.
- 4. Press and release the POWER button to power on device. Press and holdCE RECOVERY button: while pressing the FORCE RECOVERY button, press and the RESET button; wait two seconds and release the FORCE RECOVERY button
- 5. When device is in recovery mode, lsusb command on host will list a liVidia Corp"
- Warning: missing eksfile (bootloader/eks.img), continue...
- Warning: missing fbfile (bootloader/reserved_fb.xml), continue...
- copying bctfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader/BCT/P2180_A00_LP4_DSC_204Mhz.cfg)... done.
- populating kernel to rootfs... done.
- populating initrd to rootfs... done.
- populating extlinux.conf.emmc to rootfs... done.
- populating /home/nate/Downloads/TX1/Linux_for_Tegra_tx1/kernel/d210-jetson-tx1-p2597-2180-a01-devkit.dtb to rootfs... done.
- done.
- copying bcffile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader/cfg/board_config_p2597-devkit.xml)... done.
- Existing sosfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader_recovery.bin) reused.
- copying tegraboot(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloadef/nvtboot.bin)... done.
- Existing bpffile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloadern) reused.
- copying wb0boot(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader/warmboot.bin)... done.
- Existing tosfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader) reused.
- copying dtbfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/kernel/dtb/-jetson-tx1-p2597-2180-a01-devkit.dtb)... done.
- Reusing existing system.img...
- done.
- Existing tbcfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader_cpu.bin) reused.
- copying cfgfile(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader/cfg/gnu_linux_tegraboot_emmc_full.xml) to flash.xml... done.
- creating gpt(ppt.img)...
- *** GPT Parameters ***
- device size -------------- 31276924928
- bootpart size ------------ 8388608
- userpart size ------------ 31268536320
- Erase Block Size --------- 2097152
- sector size -------------- 4096
- Partition Config file ---- flash.xml
- Visible partition flag --- GP1
- Primary GPT output ------- PPT->ppt.img
- Secondary GPT output ----- GPT->gpt.img
- Target device name ------- none
- *** PARTITION LAYOUT(23 partitions) ***
- [ BCT] BH 0 8191 4.0MiB
- [ NVC] BH 8192 16383 4.0MiB nvtboot.bin
- [ PPT] UH 0 4095 2.0MiB
- [ GP1] UH 4096 8191 2.0MiB
- [ APP] UH 8192 29368319 14336.0MiB system.img
- [ TBC] UV 29368320 29372415 2.0MiB nvtboot_cpu.bin
- [ EBT] UV 29372416 29380607 4.0MiB u-boot-dtb.bin
- [ BPF] UV 29380608 29384703 2.0MiB bpmp.bin
- [ WB0] UV 29384704 29396991 6.0MiB warmboot.bin
- [ RP1] UV 29396992 29405183 4.0MiB tegra210-jetson-tx1180-a01-devkit.dtb
- [ TOS] UV 29405184 29417471 6.0MiB tos.img
- [ EKS] UV 29417472 29421567 2.0MiB
- [ FX] UV 29421568 29425663 2.0MiB
- [ SOS] UV 29425664 29466623 20.0MiB
- [ EXI] UV 29466624 29597695 64.0MiB
- [ LNX] UV 29597696 29728767 64.0MiB
- [ DTB] UV 29728768 29736959 4.0MiB tegra210-jetson-tx1180-a01-devkit.dtb
- [ NXT] UV 29736960 29741055 2.0MiB
- [ MXB] UV 29741056 29753343 6.0MiB
- [ MXP] UV 29753344 29765631 6.0MiB
- [ USP] UV 29765632 29769727 2.0MiB
- [ UDA] UV 29769728 61067263 15282.0MiB
- [ GPT] UH 61067264 61071359 2.0MiB
- copying flasher(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloader/cboot.bin)... done.
- Existing flashapp(/home/nate/Downloads/TX1/Linux_for_Tegra_tx1/bootloadelash.py) reused.
- *** Flashing target device started. ***
- ./tegraflash.py --bl cboot.bin --bct P2180_A00_LP4_DSC_204Mhz.cfg --odmd000 --bldtb tegra210-jetson-tx1-p2597-2180-a01-devkit.dtb --applet nvtboery.bin --boardconfig board_config_p2597-devkit.xml --cmd "flash;reboot"lash.xml --chip 0x21
- Welcome to Tegra Flash
- version 1.0.0
- Type ? or help for help and q or quit to exit
- Use ! to execute system commands
- [ 0.0000 ] Generating RCM messages
- [ 0.0023 ] tegrarcm --listrcm rcm_list.xml --chip 0x21 --download rcm recovery.bin 0 0
- [ 0.0036 ] RCM 0 is saved as rcm_0.rcm
- [ 0.0061 ] RCM 1 is saved as rcm_1.rcm
- [ 0.0061 ] List of rcm files are saved in rcm_list.xml
- [ 0.0061 ]
- [ 0.0061 ] Signing RCM messages
- [ 0.0081 ] tegrasign --key None --list rcm_list.xml --pubkeyhash pub_k
- [ 0.0091 ] Assuming zero filled SBK key
- [ 0.0201 ]
- [ 0.0201 ] Copying signature to RCM mesages
- [ 0.0213 ] tegrarcm --chip 0x21 --updatesig rcm_list_signed.xml
- [ 0.0231 ]
- [ 0.0231 ] Parsing partition layout
- [ 0.0253 ] tegraparser --pt flash.xml
- [ 0.0281 ]
- [ 0.0282 ] Creating list of images to be signed
- [ 0.0301 ] tegrahost --chip 0x21 --partitionlayout flash.bin --list imt.xml
- [ 0.0340 ]
- [ 0.0340 ] Generating signatures
- [ 0.0349 ] tegrasign --key None --list images_list.xml --pubkeyhash push
- [ 0.0358 ] Assuming zero filled SBK key
- [ 0.0644 ]
- [ 0.0644 ] Parsing BCT
- [ 0.0698 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.cfg --chip 0x21
- [ 0.0710 ] Copying Sdram info from 0 to 1 set
- [ 0.0772 ] Copying Sdram info from 1 to 2 set
- [ 0.0772 ] Copying Sdram info from 2 to 3 set
- [ 0.0772 ]
- [ 0.0772 ] Updating boot device parameters
- [ 0.0783 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.bct --chip 0x21 --uparam flash.bin
- [ 0.0792 ] Warning: No sdram params
- [ 0.0795 ]
- [ 0.0795 ] Updating bl info
- [ 0.0804 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.bct --chip 0x21 --unfo flash.bin --updatesig images_list_signed.xml
- [ 0.0822 ]
- [ 0.0822 ] Updating secondary storage information into bct
- [ 0.0831 ] tegraparser --pt flash.bin --chip 0x21 --updatecustinfo P21P4_DSC_204Mhz.bct
- [ 0.0849 ]
- [ 0.0850 ] Updating board information from board config into bct
- [ 0.0861 ] tegraparser --boardconfig board_config_p2597-devkit.xml --c --updatecustinfo P2180_A00_LP4_DSC_204Mhz.bct
- [ 0.0874 ]
- [ 0.0875 ] Updating Odmdata
- [ 0.0887 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.bct --chip 0x21 --ulds Odmdata = 0x84000
- [ 0.0897 ] Warning: No sdram params
- [ 0.0898 ]
- [ 0.0898 ] Get Signed section bct
- [ 0.0915 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.bct --chip 0x21 --lct_list.xml
- [ 0.0927 ]
- [ 0.0927 ] Signing BCT
- [ 0.0939 ] tegrasign --key None --list bct_list.xml --pubkeyhash pub_k
- [ 0.0947 ] Assuming zero filled SBK key
- [ 0.0954 ]
- [ 0.0954 ] Updating BCT with signature
- [ 0.0965 ] tegrabct --bct P2180_A00_LP4_DSC_204Mhz.bct --chip 0x21 --u bct_list_signed.xml
- [ 0.0977 ]
- [ 0.0977 ] Copying signatures
- [ 0.0989 ] tegrahost --chip 0x21 --partitionlayout flash.bin --updatess_list_signed.xml
- [ 0.0998 ] Run tegrabct to update tboot signature in bct
- [ 0.1012 ]
- [ 0.1012 ] Boot Rom communication
- [ 0.1023 ] tegrarcm --rcm rcm_list_signed.xml
- [ 0.1031 ] BR_CID: 0x32101001640ca5870400000018000180
- [ 0.2531 ] RCM version 0X210001
- [ 0.2646 ] Boot Rom communication completed
- [ 1.2724 ]
- [ 1.2724 ] Sending BCT and pre-requisite binaries
- [ 1.2745 ] tegrarcm --download bct P2180_A00_LP4_DSC_204Mhz.bct
- [ 1.2760 ] Applet version 00.01.0000
- [ 1.2908 ] Sending bct
- [ 1.2909 ] [................................................] 100%
- [ 1.4909 ]
- [ 1.4910 ] Retrieving storage infomation
- [ 1.4931 ] tegrarcm --oem platformdetails storage storage_info.bin
- [ 1.4946 ] Applet version 00.01.0000
- [ 1.5061 ] Saved platform info in storage_info.bin
- [ 1.5326 ]
- [ 1.5326 ] Sending bootloader and pre-requisite binaries
- [ 1.5342 ] tegrarcm --download rp1 tegra210-jetson-tx1-p2597-2180-a01-tb 0 --download ebt cboot.bin 0 0
- [ 1.5357 ] Applet version 00.01.0000
- [ 1.5500 ] Sending rp1
- [ 1.5503 ] [................................................] 100%
- [ 1.6044 ] Sending ebt
- [ 1.6093 ] [................................................] 100%
- [ 1.6890 ]
- [ 1.6901 ] tegrarcm --boot recovery
- [ 1.6910 ] Applet version 00.01.0000
- [ 1.7030 ]
- [ 1.7030 ] Flashing the device
- [ 1.7055 ] tegradevflash --pt flash.bin --storageinfo storage_info.bine
- [ 1.7069 ] Cboot version 00.01.0000
- [ 2.3934 ] Writing partition GPT with gpt.bin
- [ 2.3941 ] [................................................] 100%
- [ 2.3983 ] Writing partition NVC with nvtboot.bin.encrypt
- [ 3.3444 ] [................................................] 100%
- [ 3.3580 ] Writing partition APP with system.img
- [ 3.3930 ] [................................................] 100%
- [ 49.0636 ] Writing partition TBC with nvtboot_cpu.bin.encrypt
- [ 49.0780 ] [................................................] 100%
- [ 49.0836 ] Writing partition EBT with u-boot-dtb.bin.encrypt
- [ 49.0931 ] [................................................] 100%
- [ 49.1132 ] Writing partition BPF with bpmp.bin
- [ 49.1279 ] [................................................] 100%
- [ 49.1341 ] Writing partition WB0 with warmboot.bin.encrypt
- [ 49.1437 ] [................................................] 100%
- [ 49.1475 ] Writing partition RP1 with tegra210-jetson-tx1-p2597-2180-at.dtb
- [ 49.1537 ] [................................................] 100%
- [ 49.1665 ] Writing partition TOS with tos.img.encrypt
- [ 49.1789 ] [................................................] 100%
- [ 49.1846 ] Writing partition DTB with tegra210-jetson-tx1-p2597-2180-at.dtb
- [ 49.1935 ] [................................................] 100%
- [ 49.2159 ]
- [ 49.2168 ] tegradevflash --write BCT P2180_A00_LP4_DSC_204Mhz.bct
- [ 49.2174 ] Cboot version 00.01.0000
- [ 49.3604 ] Writing partition BCT with P2180_A00_LP4_DSC_204Mhz.bct
- [ 49.3617 ] [................................................] 100%
- [ 49.4673 ]
- [ 49.4673 ] Flashing completed
- [ 49.4674 ] Coldbooting the device
- [ 49.4690 ] tegradevflash --reboot coldboot
- [ 49.4703 ] Cboot version 00.01.0000
- [ 49.4756 ]
- *** The target t210ref has been flashed successfully. ***
- Reset the board to boot from internal eMMC.
- 1
- Finished Flashing OS
- Determining the IP address of target...
- JetPack is unable to determine the IP address of the Jetson Developer Ki
- Please select which action do you want:
- 1. Retry
- 2. Manually enter IP address
- Your option is <1/2>:
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement