Advertisement
test9999113443

Untitled

Oct 5th, 2022
68
0
Never
Not a member of Pastebin yet? Sign Up, it unlocks many cool features!
Bash 2.01 KB | None | 0 0
  1. Unlocking Kernel_RootFS ...
  2. Writing from /var/cgiL99VVJ to Kernel_RootFS ...  [w]
  3. Restarting system.
  4.  
  5.  
  6. U-Boot 1.1.3 (Mar  2 2016 - 14:05:04)
  7.  
  8. Board: MediaTek APSoC DRAM: 64 MB
  9. enable ephy clock...done. SSC disabled.
  10. ******************************
  11. Software System Reset Occurred
  12. ******************************
  13. MediaTek SPI flash driver, SPI clock: 48MHz
  14. spi device id: ef 40 17 0 0 (40170000)
  15. find flash: W25Q64BV
  16. *** Warning - bad CRC, using default environment
  17.  
  18. ============================================
  19. MediaTek U-Boot Version: 5.0.0.5
  20. --------------------------------------------
  21. ASIC 7620_MP (Port5<->None)
  22. DRAM component: 512 Mbits DDR, width 16
  23. DRAM bus: 16 bit
  24. Total memory: 64 MBytes
  25. Flash component: SPI Flash
  26. Date:Mar  2 2016  Time:14:05:04
  27. ============================================
  28. icache: sets:512, ways:4, linesz:32, total:65536
  29. dcache: sets:256, ways:4, linesz:32, total:32768
  30.  
  31.  #### The CPU freq = 580 MHZ ####
  32.  estimate memory size = 64 Mbytes
  33.  
  34. Please choose the operation:
  35.    0: Load system code then write to Flash via Serial.
  36.    1: Load system code to SDRAM via TFTP.
  37.    2: Load system code then write to Flash via TFTP.
  38.    3: Boot system code via Flash (default).
  39.    4: Enter boot command line interface.
  40.    7: Load U-Boot code then write to Flash via Serial.
  41.    9: Load U-Boot code then write to Flash via TFTP.                          0
  42.  
  43.  
  44. 3: System Boot system code via Flash.
  45. ## Checking image at bc050000 ...
  46.    Image Name:   SNR-CPE-W4N-MT
  47.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  48.    Data Size:    2181069 Bytes =  2.1 MB
  49.    Load Address: 80000000
  50.    Entry Point:  80000000
  51.    Verifying Checksum ... Bad Data CRC
  52.  
  53. ## Enter to Rescue Mode (image error) ##
  54.  
  55.  NetTxPacket = 0x83FE60C0
  56.  
  57.  KSEG1ADDR(NetTxPacket) = 0xA3FE60C0
  58.  
  59.  NetLoop,call eth_halt !
  60.  
  61.  NetLoop,call eth_init !
  62. Trying eth2
  63.  
  64.  ETH_STATE_ACTIVE!!
  65.  
  66. Our IP address is:(192.168.1.1)
  67. Wait for TFTP request...
  68. D checksum bad
  69. checksum bad
  70. D D checksum bad
  71. checksum bad
  72. checksum bad
  73.  
  74.  
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement